Статья 'Conceptual optical schemes of direction finding computational devices for guiding the space probe to a landing point on small bodies of the solar system' - журнал 'Cybernetics and programming' - NotaBene.ru
по
Journal Menu
> Issues > Rubrics > About journal > Authors > About the Journal > Requirements for publication > Council of Editors > Peer-review process > Policy of publication. Aims & Scope. > Article retraction > Ethics > Online First Pre-Publication > Copyright & Licensing Policy > Digital archiving policy > Open Access Policy > Article Processing Charge > Article Identification Policy > Plagiarism check policy
Journals in science databases
About the Journal

MAIN PAGE > Back to contents
Cybernetics and programming
Reference:

Conceptual optical schemes of direction finding computational devices for guiding the space probe to a landing point on small bodies of the solar system

Lobanov Aleksandr Anatolevich

PhD in Technical Science

Associate Professor, Department of Instrumental and Applied Software, MIREA Russian Technological University

119454, Russia, g. Moscow, pr. Vernadskogo, 78, kab. G-225

aa.lobanoff@ya.ru
Other publications by this author
 

 

DOI:

10.25136/2644-5522.2019.1.28720

Received:

21-01-2019


Published:

04-03-2019


Abstract: The subject of the research is an optical direction finder for the navigation and guiding a space probe. The usage of the optical correlation computing device is determined by the necessity to reduce the load to a space probe on-board computer system. The paper describes especially the optical correlation computing devices for building the correlation-extremal direction finders. The principle optical schemes of this class of optical devices are described. The method of mathematical modeling is used for building and analyzing the optical scheme of the proposed optical correlation computing devices. Both advantages and disadvantages of the existed optical schemes are noted. The requirements to parameters of the special on-board optical correlation computing device for the direction finding are proposed. It is shown that the optical device potentially can be used for navigation and guiding a space probe in the process of the landing on a small body of the solar system.


Keywords:

optical processing, image recognition, on-board computing system, autonomous guidance, optical computer, spatial information, optical scheme, direction finding, autonomous navigation, spatial data

Introduction

We assume that special navigation and guiding system is necessary for the precise soft landing a space probe on small bodies of the solar system. The main part of this system is a direction finder. Currently, optoelectronic tracking systems are widely used for the purposes of direction finding. These systems use the correlation analysis for support of the direction finding. This method requires a relatively small number of object’s elements for the direction finding [1-7] The performance of CE-system depends on the on-board electronic hardware. The on-board equipment is significantly less power than ground based analogs because of the demand of vibration, temperature and radiation resistance [8-10]. Thus it is very important to choose an optimal algorithm that is not overload on-board hardware.

In this paper is described an alternative approach for the navigation and guiding CE-system. It is possible to create CE-systems with correlation in the optical path [11-15]. That optical (versus electronic) CE navigation and guidance systems are characterized by the high speed and significantly lower requirements to the hardware of the on-board computing system. This paper describes the possible options for the construction of the space probe CE navigation and guidance systems based on the correlation in the optical path.

The variation of the optical elements in the system allows to build the system performs various types of mathematical operations (e.g. addition, multiplication, differentiation, integral convolution, mutual correlation, Fourier transform etc.) [11,12,16-20]. The ability of the optical systems to implement Fourier transform [8,9] could be used to build an optical direction finder with high performance [11-15].

Optical computing devices have at least three essential advantages over electronic devices with similar functions [8,9]. The first one is that the of optical direction finders are real time simultaneous two-dimensional spatial information processing complexes. Electronic CE-systems implements separate transform of a spatial information by the X coordinate and by the Y coordinate. That procedure demands more resources or could be implemented step by step. In the last case we lose real time procedure. The second is that, in optical computing devices the speed of transform does not depend on the complexity of the processed function or algorithm. The time of implementation in optical computing devices depends on the speed of the light propagation in the optical system. It implements the transform practically instant. The third advantage of the optical computing devices is a relevant simplicity of the construction, small size and light weight. All these advantages of the optical computing devices are very important for building a CE-system for navigation and guiding the space probe during its landing on the small bodies of the solar system.

Formal description of the optical correlator finder scheme

The optical CE-system implements the mutual correlation of two functions g and h. Where g and h are functions of the coordinates x, y. Functions g and h also depend on the point of origin shift. The functions g and h could be defined by the following expression [18]:

where h* – is the complex conjugate of the function h.

If the functions are identical (g(x, у) = h(х, у)), we can define (1) as follows:

The integral operation (2) is called autocorrelation function.

It is proved [15] that the module of the autocorrelation function (real or complex) has an absolute maximum at u=0, v=0:

The relation (3) allows to determine the coordinates of the shift (u,v) if we know the position of the maximum of the correlation function. The position of the maximum could be used to build the direction finding characteristics. Optical computing devices which can implement the operation of mutual correlation of two functions are called optical correlators. That class of CE-systems could be used as a part of onboard computing complex for navigation and guiding a space probe during the dissent and landing on the surface of a small body of the solar system.

It is possible to build the optical direction finder using one of two types of optical schemes. The first type is based on the coherent illumination. The coherent type is difficult to use for landing a space probe. The second type uses incoherent illumination. The principle of operation incoherent optical computing systems is based on the application of the laws of geometric optics [20]. Figure 1 presents a scheme of the incoherent optical correlator [9,18,21], which consists of two thin collecting components (lenses). The main points H1, H1', и H2, H2' are jointed.

A radiation receiver is located in the rear focal plane of the second component (analysis plane), which is optically coupled to the plane of the radiation source. The first component acts as a collimator and creates parallel beams passing through the transparencies. The second component collects in its rear focal plane the energy of optical radiation transmitted through the transparencies, i.e. performs the integration operation.

The concept of the optical computer processing is based on the fundamental of a light tube. An optical radiation energy propagation could be described as a physical light beam. It is possible to formalize a physical light beam as an elementary light tube. The light tube as a physical phenomenon is the tube that has a diameter (transverse dimensions) is infinitely small compared to its length [20]. The direction of propagation is the axis of the light tube. The wave of a light energy propagates along the axis of the light tube.

Figure 1–The scheme of incoherent optical correlator

Let us select an arbitrary off-axis point B in the plane of the radiation source and let the beam pass through the combined main points from it Н1 и Н1' at some angle to the optical axis (figure 1), Passing through the first component without refraction, the beam will cross the plane of the first transparency at point М1 with coordinates (x, y), and the plane of the second transparency at point М2 with coordinates (x+u, y+u) (the origin of the coordinate system can be chosen arbitrarily, but the axis OZ must coincide with the optical axis). After refraction on the second component, this beam will pass through the point В', conjugated to the point B.

Now let’s consider an elementary light tube, the axis of which is the specified beam. The radiation flux Ф0, going inside the light tube from the elementary site centered at point B, will be weakened when passing through the lens components and transparencies. Assuming that the transmittance of the lens components t0 is constant for all passing rays, we find the value of the radiation flux transferred by the physical beam to the analysis plane (4):

A physical integration is implemented in the reference area of the standard (АS). The area is limited by its light zone (diameter of the first optical element), and depending on the size of the aperture and the distance between the first optical element and a transparency standard q.

The expression (5) presents a two-dimensional convolution of the function τ1 and τ2. Therefore, the presented optical system allows to implement the function of mutual correlation of the investigated and referencing images.

The spatial resolution of the system is limited by the diffraction. Diffraction significantly increases at a large size of aperture AS. Theoretically it is possible to decrease the by the reducing the distance between the transparency standard and first optical element of the system. Practically that decision is not always possible for constructive reasons. This problem is eliminated in the scheme shown in figure 2.

Figure 2 – a modified scheme of the incoherent optical correlator.

Where FS – a field stop of the system; ASi – an aperture stops of the system; Fi and F’i – main points of the thin components of the optical system; Hi and H’i – main plains of the system; B1 – an off-axis ray of the object; B4 – an image of the off-axis ray of the object in the image plane.

The optical system consists of four thin components (elements), the First and fourth elements perform the same functions as the elements in the previous scheme (see figure 1). The rear focal plane of the second element coincides with the front focal plane of the third element, and the analysis plane (the rear focal plane of the fourth element) will be optically conjugated with the plane of the source of incoherent radiation (the front focal plane of the first element). The optical standard (reference image) is located in the front focal plane of the second element that is corresponded in position with the rear focal plane of the third element. The plane of the test image and the plane of the reference images are optically conjugated. That solution allows to reduce the distance between the test image the reference image in the real system almost equal to zero (q=0). Aperture stop is a frame of the transparency standard (reference image) (see. figure 1). The advantages of the this scheme is the possibility of changing the scale of the studied and reference images, depending on the ratio of the focal lengths of the second and third elements. In particular, at the same focal lengths of the second and third components F2' и F3' the scales of the studied and reference images will be equal. However, the longitudinal dimensions of the optical system in the second case (figure 2) are much larger than in the first case (figure 1).

The presented optical systems of incoherent correlators (CE-systems) allow processing only unipolar signals. However, it is possible to introduce a constant component into the optical scheme and change the sign of the signal. The last method produces significant background signal would be registered by the radiation receiver. The problem is that the background signal usually exceeds the useful signal. The first part of the problem decision is the movement (transfer) the radiation receiver in the analysis plane. The second part of the solution to eliminate the background signal must be provided the mutual movement of the test and reference images [18]. The movement of the images demands (requires) some technical solution that performs these movements. A significant drawback of the previously described schemes is the need to use several similar devices (for example, three or four) to create a direction finding characteristic and a control signal [22, 23].

To obtain a multichannel CE-characteristic for navigation and guiding a space probe on the landing site at a surface of the small body of the solar system the optical direction finder has to: 1) consist of several optical correlators; 2) the Radiant flux should be proportional to the area of correlation (object image) and transmission of the standard recorded by the radiation receiver; 3) to reduce the effect of uneven sensitive areas of the radiation receiver, it is necessary that the illumination of the exit pupil of the direction finder over its entire area is uniform; 4) to fulfill this condition, the optical system of the direction finder must be free of vignetting.

Results

Two conceptual schemes of optical correlators which can be used for building the optical direction finder for navigation and guiding of a space probe are proposed. The usage of the optical direction finder is determined by the necessity to reduce the load to the on-board computer complex of a space probe. The combination of several optical correlators allows to determine the angular position of the landing site on a small body of the solar system. The optical direction finder mathematical model is built. This model is used for analysis of the proposed optical correlators. Both advantages and disadvantages of the optical schemes are discussed. It is shown that the optical device potentially capable to guide a space probe to the landing point on a small body of the solar system. We assume that, the proposed schemes of the optical correlator have a number of significant advantages. The usage of direction finders build on the scheme of the proposed correlator reduces the resource requirements to the onboard computer complex, which is important for the creation of on-board autonomous guiding and navigation system of the space probe. The solid construction of the optical computing device and the relevant simplicity of the design increase the reliability of the on-board computing complex. The requirements to the parameters of the prospective optical correlation direction-finder are determined.

References
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Link to this article

You can simply select and copy link from below text field.


Other our sites:
Official Website of NOTA BENE / Aurora Group s.r.o.